Real-hardware finding: a SuperSpeed hub (the user's Genesys, 4 SS
downstream ports) HUNG the bus driver at boot — it stopped logging with
no fault, and the hub's port power dropped. Cause: a SuperSpeed hub has
change bits a USB2 hub lacks (link-state, BH-reset), and the B4 servicing
— written and tested against QEMU's USB2 hub — never cleared them, so
the hub's status-change endpoint re-reported the same port forever and
the driver spun servicing it, never reaching the USB2 companion hub
where the full-speed keyboard actually lives.
hubPortStatusAck now clears the SuperSpeed-only change features too
(gated on hub speed; a USB2 hub is unaffected), and the tick services a
bounded batch of hub changes (32) before yielding — so even if a hub's
change bits misbehave, the driver cannot spin the machine. A per-port
status log line surfaces exactly what a hub reports, so the next real
boot shows the SS hub's port states and whether the USB2 companion
enumerates. QEMU usb-hub cases still green (the SS clears are gated off
for QEMU's USB2 hub).
Completes hub support (docs/usb-hub.md). On the bus tick, a downstream
hub-port change now dispatches: a connect enumerates the new device
(B4b), a disconnect tears the old one down — recursively, since a hub
that leaves takes its whole subtree with it (children first), reporting
each interface ChildRemoved and Disable-Slotting the device. Route
strings compose across tiers, so a device two hubs deep enumerates with
a two-tier route.
QEMU's hub — unlike root-port hot-plug — DOES raise downstream
status-change events, so both paths are harness-tested: usb-hub (a
keyboard behind a hub binds usb-hid-keyboard), usb-hub-nested (a
keyboard two hubs deep), usb-hub-unplug (device_del behind the hub tears
it down). Full suite 91/91.
Real-hardware validation of the user's SuperSpeed Genesys hub with
full-speed devices on its USB2 companion is flagged for the user (QEMU's
USB2 hub does not model the compound USB3 hub).
The core of hub support (docs/usb-hub.md): a device on a hub's
downstream port now reaches its class driver exactly like one on a root
port. The hub's interrupt status-change endpoint is armed with an
in-process subscription — completions set the hub's pending-port mask
instead of queuing a class-driver report — and setupHub seeds every
downstream port pending so a STATIC topology (a device present at
power-on) enumerates without waiting on the initial interrupt edge.
On the bus tick, each pending hub port is serviced: GET_STATUS + clear
the change bits, and on a connect reset the port, read the speed, then
enable a slot and Address Device with the composed route string
((parent_route<<4)|port), the inherited root port, and the parent hub's
slot/port as the TRANSACTION TRANSLATOR — so the controller routes a
full/low-speed device's split transactions through the hub's TT. The
device then enumerates and registers its interfaces through the normal
path (a compact topology-unique port key keeps the id tag within its
8-byte cap), recursing setupHub if it is itself a hub.
Verified in QEMU (a keyboard behind a USB2 hub on a second controller):
'hub slot 1 port 1 device vendor 0x0627 ... usb-hid-keyboard: ok
(device 35)'. Full suite 89/89. The user's SuperSpeed Genesys hub +
full-speed keyboard/mouse on its USB2 companion is the real-hardware
target, flagged separately.
First slice of hub support (docs/usb-hub.md), handled IN the xhci-bus
because a device behind a hub is reached by the CONTROLLER via a route
string in its slot context — topology only exists inside the driver
that owns the controller. When the scan enumerates a class-9 device it
now calls setupHub: read the hub descriptor for the downstream port
count and TT arrangement, tell the controller the slot is a hub
(Configure Endpoint with the slot add-flag sets the Hub bit, Number of
Ports, and MTT/TT-Think-Time per xHCI 4.6.6), SET_HUB_DEPTH for a
SuperSpeed hub so it can compose route strings, and SET_FEATURE
PORT_POWER every downstream port.
The Device gains topology fields (route string, root port, parent hub
slot/port for the TT) and buildAddressInputContext now fills them, so
the Address Device path is ready for downstream devices — those are
enumerated in B4b. A root-port device gets route 0 and its own port as
the chain root, unchanged behavior.
Verified in QEMU with a hub on a second controller and a device behind
it (a usb-hub QEMU case, since the boot controller's auto-assigned
devices collide on the low ports): 'hub slot 1: 8 downstream ports
powered (USB2 single-TT)'. Full suite 89/89. The user's SuperSpeed
Genesys hub is the real-hardware target, flagged separately (QEMU's
USB2 hub doesn't model the compound USB3 hub).
Regression from the B3 MPS0 work, caught on real hardware: a SuperSpeed
hub (and the SuperSpeed boot stick) failed to enumerate. bMaxPacketSize0
(device descriptor byte 7) is a LITERAL size for USB 2.0 and below
(8/16/32/64) but an EXPONENT for SuperSpeed (9 = 2^9 = 512). The refresh
read the exponent 9 as a size and issued Evaluate Context to set EP0 to
9 bytes, corrupting the control endpoint so every following transfer
failed. SuperSpeed's EP0 is fixed at 512 and needs no correction, so
the refresh is now skipped for speed >= 4; only full/low/high speed,
where the field is a literal that can differ from the speed default,
still run it. QEMU tolerated the wrong MPS0 — real silicon does not
(the class of bug the harness can't reach, flagged real-HW-pending).
This likely also explains intermittent no-storage/no-logs on a normal
boot: the boot stick is SuperSpeed and hit the same corruption. Full
suite green (orderly-shutdown's lone failure was its known QMP-timing
flake — three clean re-runs).
B3 — the runtime lifecycle a hot-pluggable bus needs, plus two init
fixes that runtime device arrival depends on:
- pump() now handles PORT STATUS CHANGE events (silently dropped
before): it queues the port, and the bus driver brings the port up
(a device arrived) or tears it down (a device left) on its tick —
reporting each interface ChildRemoved to the device manager, which
prunes the node, notifies watchers, and lets the class driver's world
end honestly, then Disable Slot frees the controller-side state.
- ALL root-hub ports are powered at init, not just those with a
boot-time device: an unpowered port (PP=0) cannot signal a later
connect, so a hot-plug would never be seen.
- the interrupter is enabled (IMAN.IE + USBCMD.INTE) while the ring
stays polled — some controllers only WRITE runtime events to the
ring when the interrupter is enabled.
Real-hardware validation is flagged for the user: QEMU's qemu-xhci does
not raise a runtime port-change event to a polling driver on device_add,
so the end-to-end hot-plug path can't be exercised in the harness (the
port-change handling itself IS proven — a late boot device's PSCE is
caught and acked). The harness gained qmp_sequence (multi-step QMP
injection with arguments) for when a drivable case exists. Full suite
88/88; the working USB path (enumeration, HID, storage) is unregressed
by the port-power and interrupter changes.
Two real-hardware correctness fixes from the M20 list, both invisible
to QEMU's forgiving controller:
refreshMaxPacketSize0 existed only as a comment. The EP0 context kept
the SPEED-DEFAULT max packet size (full-speed: 8) even when the device
declares 16/32/64 — real controllers fault the very first full
descriptor read on the mismatch, which is the standing suspect for
full-speed mice dying on the user's PC. Enumeration now probes the
device descriptor's first 8 bytes (deliverable at any legal MPS0),
and issues Evaluate Context to correct EP0 before any longer transfer,
naming the failure and codes if the controller refuses.
And a USB2 port's PORTSC speed field is only meaningful once the port
reset ENABLES the port: the speed (and the MPS0 default derived from
it) is now sampled after the reset instead of trusting the connect-time
read.
B2 — the 1-in-3 boot-time READ CAPACITY failure, root-caused: the xHCI
library's awaitTransfer claimed ANY unclaimed transfer event as its own
completion. An interrupt-endpoint event whose TRB pointer no longer
matched the armed subscription (an error or stale completion from the
keyboard/mouse polling concurrently with storage bring-up) fell through
and was misread as the bulk transfer's completion — desynchronizing the
mass-storage bulk protocol in controller state that SURVIVED driver
restarts, so every retry failed too. Awaited transfers now match the
event's slot id and endpoint DCI; foreign events are dropped and named.
Twelve consecutive runs of the previously-flaky cases pass; the full
suite is green with none of its old intermittents.
B1 — and when storage does fail transiently, the system now heals
instead of giving up forever: a nonzero exit maps to ExitReason.aborted
(a deliberate FAILURE exit — supervisors restart those with backoff,
unlike a clean .exited), usb-storage exits nonzero when a PRESENT
device fails bring-up, and the fat service no longer blocks its harness
polling for a block device and then dies — it serves immediately
(requests fail politely), retries on a 500 ms timer, and mounts
whenever storage appears, including after a driver restart.
Real-PC diagnose boot (photo + OCR): the boot stick connects at
SuperSpeed on port 21 and 'device setup failed' lands in the SAME
millisecond — an instant failure, not a timeout. setupDevice reset
every port unconditionally; that is required to enable USB2 ports, but
a SuperSpeed port that trained its link is ALREADY enabled (xHCI
advances USB3 ports to Enabled, no reset — spec 4.3), and driving a hot
reset into the live link drops PED mid-reset on real silicon. QEMU
tolerates the spurious reset, which is why the harness never saw it.
An enabled speed>=4 port now skips the reset (a not-yet-enabled SS link
still gets one). Every setup step names its failure — port reset with
the PORTSC value, Enable Slot, device-slot exhaustion, Address Device
with its completion code — so the on-screen transcript of the next
failure identifies the exact xHCI command instead of one blanket line.
block.open's give-up window drops 60 s -> 30 s (the slowest observed
healthy chain completed at ~24 s); a machine whose stick failed setup
should not sit a further minute pretending otherwise.
Flesh out the xHCI host-controller driver into a full transfer engine and build
the three USB class drivers on top, all verified end to end under QEMU.
- xHCI engine (usb-xhci-library.zig): controller reset, command/event rings with
cycle-bit bookkeeping (gated on a No-Op-command proof), device slots, Address
Device, control transfers, full chapter-9 enumeration, Configure Endpoint, and
interrupt/bulk transfers. Each interface is device_registered with its
(class,subclass,protocol) identity, unique per (port,interface).
- Bus<->class transfer protocol (usb-transfer-protocol.zig + runtime.usb): open /
control / interrupt-subscribe (async report pump on a poll timer) / bulk-by-
physical-address, so sector data never crosses the 256-byte IPC limit.
- USB HID keyboard + mouse (usb-hid/): decode boot-protocol reports and publish
to the input service. A USB usage is already the input protocol's keycode.
- USB mass storage (usb-storage/): Bulk-Only Transport + transparent SCSI,
serving a block device under the new .block service id (block-protocol).
- device-manager matches USB interfaces to class drivers (usbDriverForIdentity).
- usb-abi / usb-ids made importable modules; add HID and mass-storage class
requests, packTriple, and a usb_device DeviceClass.
- Fix test/qemu_test.py on macOS: the QMP unix-socket path was built from the
deep worktree path and exceeded the 104-byte sun_path limit, so QEMU exited
before booting. It now lives under a short temp path.
Tests: usb-report, usb-hid, usb-storage pass under python3 test/qemu_test.py;
host units (usb-abi, usb-ids, hid-report, bulk-only-transport, scsi) green.
Daniel Samson